產品展示
              首頁 > 產品展示 > 3240環氧板 > 彩麗膜 > 聚酰亞胺薄膜F46膠帶

              聚酰亞胺薄膜F46膠帶

              描述:聚酰亞胺薄膜F46膠帶

              更新時間:2015-11-24
              產品型號:6254-FN
              廠商性質:生產廠家
              詳情介紹

               6254-FN 聚酰亞胺薄膜F46膠帶

               

              執行標準:KAPTON*FN型絕緣膜

              適用范圍:
              該產品是由TY6051—FN型聚酰亞胺薄膜單面或雙面涂以F46膠經干燥分切而成的膠帶(以下簡稱膠帶)。該膠帶使用于做電工導線繞包絕緣材料,在350℃—380℃溫度下0.5min 熔融成型。

              技術參數:
              1.外觀:膠帶應干爽、平整、無氣泡、無雜質
              2.尺寸
              1)長度
              膠帶長度及接頭數根據用戶要求,滿足其需要。
              2)寬度
              膠帶的寬度及允許偏差為10mm±0.5mm、15mm±0.5mm。根據用戶需求可提供其他寬度規格的膠帶。
              3)膠帶的標稱厚度及允許偏差應符合下表規定

              Kapton*FN 規格 120FN 616B 150FN019 200FN919
              TY6254—FN 規格 0.033mm雙面 0.038mm單面 0.05mm雙面
              標稱厚度 mm 0.033 0.038 0.05
              允許偏差 mm +0.003
              -0.003
              +0.004
              -0.004
              +0.006
              -0.004

              3.性能要求:

              項目名稱 性能指標
              厚度(mm) 0.033雙面 0.038單面 0.05雙面
              縱向伸長率 % ≥55 ≥55 ≥55
              介電強度 KV/mm

              ≥197

              ≥157

              ≥130

              剝離強度
              N/10mm
              膠面—膠面
              膠面—底材
              膠面—銅材

              ≥2.3
              不合適
              ≥2.3

              不合適
              ≥2.3
              ≥2.9

              ≥3.5
              不合適
              ≥3.5


              包裝、標志、貯存和運輸:
              1、膠帶卷、盤應卷在塑料或紙管芯上,然后裝在塑料袋內,封好袋口再裝入內襯訪潮紙的木箱或干燥潔凈的紙箱內。
              2、每一包裝中應附有產品的檢驗合格證,箱體上標明產品名稱、規格批號、毛重、凈重、生產日期、生產廠名稱,及“防潮”“防沖擊”等字樣。
              3、該產品從生產之日起貯存期為六個月。超過貯存期按本標準進行檢驗,合格者仍可使用。
              4、膠帶應貯存在避光、干燥、潔凈、通風良好的庫房中。
              5、膠帶運輸時,應避光、防潮、不得重壓、摔打和機械損傷。

              6254-FN Polyimide Film Adhesive Tape F46

              Executive Standard: KAPTON*FN insulating film
              Standard No: TY6254-FN
              Applicable Range: This product is manufactured with the raw material of polyimide film painted with F46 adhesive on single or both sides. After drying, it has been cut into different width. The product can be used for electrical lead winding insulating material. This product is fused at the temperature from 350℃ to 380℃ at 0.5 minute.

              1.Technological requirement:
              1.1 Appearance:
              The tape should be dry, clean and smooth and the tape should have no defects such as air bubble, pinhole, elc.
              1.2 Dimension:
              1)Length: The length of the tape as well as the number of splice should be made as the requests of client.
              2)Width: the width of the tape and its tolerance is as follows: 10mm±0.5mm, 15±0.5mm other width of tape is available too.
              3)The tape’s standard thickness and its tolerance is as follows:

              Kapton FN Spe 120FN 616B 150FN019 200FN919
              TY6254-FN Spec 0.033mm double sides 0.038mm single side 0.05mm double sides
              Standard thickness mm 0.033 0.038 0.05
              Tolerance mm +0.003
              -0.003
              +0.004
              -0.004
              +0.006
              -0.004

              1.3.Performance:

              Item Index
              KAPTON * Type 120 FN616B 150FN019 200FN919
              Thickness(mm) 0.033 double sides 0.038 single side 0.05 double sides
              Elongation % ≥55 ≥55 ≥55
              Dielectric strength KV/mm  

              ≥197

               

              ≥157

               

              ≥130

              peeling strength
              N/10mm
              adhesive—adhesive
              adhesive—tape
              adhesive—copper
               

              ≥2.3
              N/A
              ≥2.3

               

              N/A
              ≥2.3
              ≥2.9

               

              ≥3.5
              N/A
              ≥3.5

              2.Packing, marking, storage and transportation
              2.1 The film, tape should be rolled on the plastic or paper core. Put it into a plastic bag. After sealing the bag, put them into a wooden or dry paper box. with desiccant in it.
              2.2 The test report should be put into the box. Each box should have product’s name, specification, batch number, gross weight, net weight, production date, manufacturer, dampproof as well as impact-proof on it.
              2.3 The shelf life is 6 months. It still can be used if the quality is ok after inspection.
              2.4 The product should be stored in a lightproof, dry, clean, and ventilated warehouse.
              2.5 On transportation, the product should avoid sun light, humidity. The product should not be stressed, breaked and avoid mechanical manage.

              留言框

              • 產品:

              • 您的單位:

              • 您的姓名:

              • 聯系電話:

              • 常用郵箱:

              • 省份:

              • 詳細地址:

              • 補充說明:

              • 驗證碼:

                請輸入計算結果(填寫阿拉伯數字),如:三加四=7
              技術支持:化工儀器網   sitemap.xml   管理登陸
              ©2025 上海徐吉電氣有限公司(m.mp3shek.net)版權所有   備案號:滬ICP備15015674號-62
              中文有无人妻vs无码人妻激烈 | 中文字幕av在线| 精品亚洲AV无码一区二区三区 | 一区二区三区观看免费中文视频在线播放| 免费无码午夜福利片69| 亚洲成a人在线看天堂无码| 日韩精品无码免费专区午夜不卡| 91久久精品无码一区二区毛片| 日本乱人伦中文字幕网站| 国产羞羞的视频在线观看 国产一级无码视频在线| 久久久噜噜噜久久中文福利| 日韩AV无码久久一区二区| 国产高清中文欧美| 亚洲精品无码永久在线观看| 日韩AV无码中文无码不卡电影| 亚洲乱码中文字幕综合234| 中文无码精品一区二区三区| 少妇人妻偷人精品无码视频| 中文字幕1级在线| 亚洲最大激情中文字幕| 国产精品无码久久久久| 国内精品人妻无码久久久影院导航 | 中文字幕专区高清在线观看| 人妻少妇伦在线无码专区视频| 自拍中文精品无码| 今天免费中文字幕视频| 四虎国产精品永久在线无码 | 精品无码一区二区三区亚洲桃色 | 日本一区二区三区中文字幕 | 人妻无码αv中文字幕久久| 免费A级毛片无码A∨免费| 无码中文字幕日韩专区视频| 西西4444www大胆无码| 国产精品无码A∨精品影院| 亚洲av无码一区二区三区网站 | 欧美乱人伦人妻中文字幕| 日韩中文字幕精品免费一区| 久久伊人亚洲AV无码网站| HEYZO无码综合国产精品227| 无码人妻精品一区二区三区久久久 | 无码精品国产VA在线观看|